• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by amcphee

  1. A

    Eaton 5005a clutch settup procedure needed

    check out attached pg. 27. Is this it?
  2. A

    Eaton 5005a clutch settup procedure needed

    Thanks Truck Shop! Will take a look
  3. A

    Eaton 5005a clutch settup procedure needed

    Need a little help guys. I have a fuller fs 5005a transmission and a pull clutch. I have looked all through the Eaton sites and cannot find how to set this pull clutch that came WITHOUT a clutch brake. It is on a 1978 Ford F800.
  4. A

    Clutch trouble shooting

    Need a little help guys. I have a fuller fs 5005a transmission and a pull clutch. I have looked all through the Eaton sites and cannot find how to set this pull clutch that came WITHOUT a clutch brake. It is on a 1978 Ford F800.
  5. A

    Bobcat T320 won't go into fast mode

    Hey guys. Quck question. How to the motor mounts install? I want to make sure they are on right. Is the red line where the bottom frame is, so the bolt is the only thing on the frame side?
  6. A

    Bobcat T320 won't go into fast mode

    installed noew shieve for power band belt. Vibration calmed down some. Have new engine mounts to install will keep you guys informed. The other issues previously written about have all been corrected with the fixes I have written.
  7. A

    Bobcat T320 won't go into fast mode

    also how do the engine mounts go onto the machine. The exploded picture does not show it attaching to the frame, just the engine/pump frame, not the machine frame mounts. We mounted them with the bolt and rubberized washer on one side of the machine frame, then the big rubber between engine...
  8. A

    Bobcat t320, multiple error codes

    in the future disconnect all connectors in cluding the computer ones, clean them with cleaner and spray them with Deoxit Gold.
  9. A

    Bobcat T320 Fuel Sending Unit

    That is where it is on the left side looking from the back. Take the panel cover off on the left size above the drive motor and you can see it. You have to reach in from below the cab and fell your way. It has a 3 wire connector, take it off and unscrew it from the tank. You need long arms...
  10. A

    Bobcat T320 won't go into fast mode

    Any idea how to set this idler stop (39)? Is it only used for locking the idler to change the belt?
  11. A

    Bobcat T320 won't go into fast mode

    I wouldnt think so either. I checked (but will double check again). Bearings ok on tensioner, motor mounts correct and tight. Hydrostat mounded correctly there is no other way to mount it. I have access to a vib pen. Any idea what is good or bad in mills?
  12. A

    Bobcat T320 won't go into fast mode

    Well guys. Checked behind my son. he had the hoses reversed on the new drive motor. :). As for the vibration, still a quesiton if you have any experiance
  13. A

    Bobcat T320 won't go into fast mode

    Thanks guys. I just finished replacing the hydrostatic pump and the right hand final drive (was leaking around seal) All case drains replaced, all hoses replaced. Unit calibrated with no codes!!! On the new rex roth pump, the connector is way different and I had to buy triangle plugs from...
  14. A

    Bobcat T320 won't go into fast mode

    Well, went ahead and pulled the motor and replaced the pump with a new Bosh/Rexroth. Hooking up hoses this weekend. Will let you guys know.
  15. A

    Bobcat T320 won't go into fast mode

    Pulling motor to look at hyd pump and swash plate bushings for sensors
See more
Top