• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by bustedknuckle

  1. B

    2011 Kubota SVL90

    Seat switches are a problem, but I have also found the seat pan will break the two rear welds loose from the seat frame. This allows the seat pan to flex, and will not compress the switch. Remove the seat with base and put it on a table. Remove the seat from the base and try pushing upwards...
  2. B

    slv 90-2

    You must have either the Kubota diagnostic software and the interface box, or there might be an aftermarket solution like a texa laptop and harness. The connector is under the cover behind the right side armrest.
  3. B

    Question on Kubota SVL90-2 (2014 model) and opinions?

    I would like to add on some other issues that I forgot in my first post. 1: Keep the belly pan cleaned out. I believe the operator's manual states to do that every 200 hours. Debris buildup combined with engine vibration/motion can cause the gear pump suction flange the break loose, causing a...
  4. B

    Question on Kubota SVL90-2 (2014 model) and opinions?

    I've been working as a Kubota dealer mechanic for over 4 years now, so this is what I can tell you. Overall, 90-2s are a good machine, but do have their issues. Went through a rash of gear pumps a while ago, Kubota upgraded the pumps with larger bushings and that seems to have solved that...
  5. B

    older bobcat 331.....no joystick funtion. Help!!

    Do your track and blade functions still work?
  6. B

    Bobcat wiring schematic

    I haven't had a chance to check it out, but the customer stated that it's blowing the 5A switch power fuse.
  7. B

    Bobcat wiring schematic

    Does anyone have access to wiring schematics for a Bobcat S570, S.N. A7U711463 SJC controls?
  8. B

    T300 Bobcat leaking pump

    No need to tear the whole motor down. It's leaking between the brake housing and the main housing. With the motor off the machine, remove the small allen bolts on the backside. Loosen them one turn at a time working your way around the bolt pattern. The cone spring for the brake is under...
  9. B

    Bobcat t200- heavy smoke under load

    The blowby tube on that engine tee's into the intake piping just ahead of the turbo.
  10. B

    bobcat heat /air

    If you just want heat, I believe they offer that as a kit. I know the whole kit, a/c and heat, can be a real PITA
  11. B

    Bobcat t200- heavy smoke under load

    A little bit of oil in the intake piping is normal due to blowby. You could have a blown head gasket, and with that engine being oil cooled, instant smoke machine.
  12. B

    BOBCAT 873 Deutz - head gasket

    Head bolt length is 5.90" +/- 0.03. And they call for a light coat of engine oil on the threads
  13. B

    BOBCAT 873 Deutz - head gasket

    Head bolt torque specs in ft.lbs. : 22, 59, 118, then an additional 90 degrees. Torque Sequence 8 6 4 5 9 10 3 1 2 7
  14. B

    Bobcat 435 Drive Belt R&R

    Atco, it's somewhat like a loader drive belt, except the engine is on one side of the drive belt housing, and the pumps are on the other side.
  15. B

    Replacing Bobcat loader control valve seals

    You can also wrap a rag around the detent sleeve and pull it off. That will catch the detent balls.
See more
Top