• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Driver2022

  1. D

    Is this for a manual tach?

    There is a spring inside there alright which that spinning pin seems to go into. I'm looking for somewhere on this Isuzu 4bd1 tengine where I can put in a manual oil pressure gauge with a capillary tube.
  2. D

    Is this for a manual tach?

    Should have added the smaller piece with the probe screws into this piece below which in turn screws into the bottom of the filter housing
  3. D

    Is this for a manual tach?

    I screwed this piece out of under the oil filter housing. The probe at the end spins as if it's a tacho of some sort? Could it be the tacho for the revs? The engine is a 4bd1 turbo
  4. D

    Oil pressure gauge installation

    There was no wiring diagram with this. Which wire goes where? I think this model has some function of a background light so maybe a wire is there for that but I don't need the background light. Also the wires that came arnt long enough. Is it OK to add to them using single core wire?
  5. D

    Oil pressure gauge installation

  6. D

    Isuzu 4bd1

    Have a machine here with an Isuzu 4bd1t engine in it. I'm wondering can I buy a kit with both the sensor, wire and clock which will read the oil pressure. I'm looking for something I can screw into the engine and then have a clock reading the pressure in the cab? I currently have nothing.
  7. D

    Isuzu 4bd1t engine

    So from the part numbers you gave the sensor seems available to buy from new but the tacho isn't showing up. Do I need that specific tacho or is there an alternative way around it?
  8. D

    Isuzu 4bd1t engine

    Anyone know where I can plug a tacho cable into in a 4bd1t engine? The altenator doesn't have this function for it. I was hoping maybe there was a sender unit I could buy and plug into the 4bd1t engine somewhere to read revs and hours
  9. D

    Replacing a 4 cylinder engine with a 6 cylinder

    Where it's lacking is when it gets very steep it is like the machine dies back a fraction and slow to move. I don't have the rev guage working but let's say at full throttle it's revving to 2200rpm but when under pressure might die back to 1900rpm or so. Could I increase the revs to around...
  10. D

    Clark Michigan 55B

    Is it solonoids change gear in the 55b out of curiosity?
  11. D

    Replacing a 4 cylinder engine with a 6 cylinder

    Yes the same flywheel and bolt pattern as far as I know
  12. D

    Replacing a 4 cylinder engine with a 6 cylinder

    It is very good to stay cool at the moment anyway as it has a very big rad in it. Is it also running very clean. Almost no black smoke under load
  13. D

    Replacing a 4 cylinder engine with a 6 cylinder

    Yes I agree with everyone that it's a great engine and sips fuel but I would just like some more power. When up a silage clamp it is just lacking 10 or 20hp I feel. What horsepower is a 4bd1t engine? I thought a 6 cylinder Isuzu might just have that big more go
  14. D

    Replacing a 4 cylinder engine with a 6 cylinder

    It's a furukawa fl310. It current has an Isuzu 4bd1 4 cylinder turbo engine in it. I'm wondering could I fit in an Isuzu 6 cylinder 6bd1 engine instead. I could push the rad back a few inchs. I'm wondering though will it bolt in at the front or not,
  15. D

    Weak tilt

    Would it be possible to disconnect the pipes off this ram and put a guage on the pipes to test what pressure coming to the ram? Like you can do to test the back of a tractor
See more
Top