• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by sepulchral

  1. S

    deere 85g, runs - raise lap bar - shuts off - ??

    great thank you. this almost seems like a variant of the autoshutdown mode
  2. S

    deere 85g, runs - raise lap bar - shuts off - ??

  3. S

    deere 85g, runs - raise lap bar - shuts off - ??

    thank you so much. do you have Starting and Charging Circuit THeory of Operation
  4. S

    deere 85g, runs - raise lap bar - shuts off - ??

    deere 85g (2014) runs fine but when you engage the safety lever after first start (hydraulics lock) the screen says "SYSTEM ENDING" and machine shuts off. will not start again for about 10 - 15 minutes. is this some kind of safety shutdown mode? what should i check?
  5. S

    kubota svl95-2s - loader arms fall freely - checked multiple things running out of ideas

    ive had Control valve apart, nothing...
  6. S

    kubota svl95-2s - loader arms fall freely - checked multiple things running out of ideas

    i know. its a simple hose with an on off plunger valve. i did check the valve its normally closed, so its ok
  7. S

    kubota svl95-2s - loader arms fall freely - checked multiple things running out of ideas

    swapped overload relief valves, that didnt fix it.. ordered a bspp cap set to see if one of the cylinders is bypassing
  8. S

    kubota svl95-2s - loader arms fall freely - checked multiple things running out of ideas

    thats not it
  9. S

    kubota svl95-2s - loader arms fall freely - checked multiple things running out of ideas

    kubota svl95-2s loader arm is falling freely. If you push down on the ground you can lift the front end of the machine up and it will stay overnight..... but if you raise arms a little they will just fall. i checked float solenoid valve looks okay. lift arm spool looks okay. thought...
  10. S

    TAKEUCHI TL12R2 creeps in reverse

    Have a takeuchi TL12R2 if machine is on a hill with the front facing up hill it will creep backwards with safeties disengaged it will also do this on level ground. When i travel forward diagonally machine wont stop for a second or two. Almost feels like the pilot resolver block on the...
  11. S

    Replaced BSI/Controller in Bobcat T250 from a S205 (same part number) and i am in ACS lockout

    Machine is Hand/Foot control only. have errors 32-04 and 09-22 i belive. all i did was replace the controllers. is there a way to calibrate the controller for hand/foot without a computer?
  12. S

    Komatsu PC78MR6 Breather to bellhousing (coupler) spitting oil?

    WHat would cause this? bad rear main seal?
  13. S

    Rebuilt first yanmar diesel - smokes a little at high load/throttle? rings need to seat?

    Dude I emailed the Chinese folks on Amazon for pistons and rods and bearings and they sold me what I needed for $480 shipped I measured the weight of pistons new versus old and mic checked all dimensions and they were exact. High quality parts too
  14. S

    Rebuilt first yanmar diesel - smokes a little at high load/throttle? rings need to seat?

    I honed them. Wel I ran machine hard and it smoked real heavy for 10min then shut it off and smoke was still coming out of muffler. Like burning oil. Started again an hour later and zero smoke at high load. Might have been residual oil
  15. S

    Rebuilt first yanmar diesel - smokes a little at high load/throttle? rings need to seat?

    by the way, at idle the oil cap will sit and bounce around on the oil fill neck, not enough blowby to push it off onto the ground. so i guess thats good
See more
Top