• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. W

    Case 850b Track Loader

    Wolfe Grading I have a total rebuilt final drive with new gears
  2. W

    850B master cylinder repair

    Try tractorzone.If you do not find one I have a good used one and I also have a lot of rebuilt parts for 850b.Trans.-Engine-Final drives-convertor-Whole parts machine.
  3. W

    Case 1450 suction filter?

    Kevin,I did not take off hitch,that is where I put my jack right near the pin hole.The weight of the weight is towards the back so the hitch provides leverage.I will try to make a drawing and send it.The weight is the worst part of the job.You could unhook one of the lines at control valve that...
  4. W

    Case 1450 suction filter?

    Kevin.You have a safe 4th. too.We will be working our Weekend job.We have a winery/Wolfe Wines.And yes those are the rings.Hope that is your problem.If the caps have a deep groove I will find the name of the place that rebuilt mine.The caps a very costly.You could check the ones in front first...
  5. W

    Case 1450 suction filter?

    There are two seal rings under each cover,three under center cover,fluid goes through hole in shaft in between seal rings,comes out in between seal rings in clutch housing to engage clutches.Center cover is hi range/lo range.Also two more in front of trans.1st.& 2nd. for each track.These rings...
  6. W

    Case 1450 suction filter?

    There are two in front 1st & 2nd for each track.Three in rear hi range/lo range under center cover,forward & reverse for each track under other two covers.I block the weight very good then drive loader away from it.You can call me 336-3763038 after 8:00
  7. W

    Case 1450 suction filter?

    I think that hose is converter drain to transmission.Mine has hose clamps on that hose.if hole in control is clogged it would not go in any gear very well.I would check seal rings before I took off control valve.They are not very costly.Sounds like you are losing fluid going to clutches.But the...
  8. W

    Case 1450 suction filter?

    Kevin,If you decide to remove weight to check seal rings.I block up the weight then use bottle jack under hitch on weight,then pull the loader away from it.Then install in reverse order,be very careful doing it that way!!!Sometimes the caps over the shafts have a deep groove from the seal...
  9. W

    Case 1450 suction filter?

    Kevin,The orifice spool is not under pressure,the spring & roll pin should come out first.Blowing air will not get it out, I tried!!!The way I got it out was with a magnet attached to a bolt.Other than removing control valve.Have you checked seal rings on transmission shafts.Also it should have...
  10. W

    Case 1450 suction filter?

    Kevin,Sounds like the range orifice spool you could not get out.I used a long bolt with magnet to pull it out.Also when you said the screen was torn /modulator filter,there is a small hole in valve body to modulator orifice that could be stopped up since screen was torn.Are you sure the pump is...
  11. W

    Case 1450 suction filter?

    My 1155 has had problems like yours.There was a broken spring on range orifice in back of control valve.Another time air entering suction line to pump which you have already talked about.The noise you are hearing are most likely clutches.Also had trash in hole in modulator orifice one time that...
  12. W

    Case 850b Track Loader

    I have owned a Case 850b Track Loader for 15 years.I have rebuilt every part on one and also own a Case 1155D that I know from front to back.I have a lot of good used parts for 850B.Would also be glad to help someone on repair questions.This is my first time posting. Wolfe Grading
Top