• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. E

    cat mt835 no forward or reverse

    machine will turn, gear shifts, goes into neutral and park, will not move. code reads j1939 data link not commincating. serial number on machine is mt835pbam30361. mice got into machine so I think a wire is broke anybody have a electrical schematic.
  2. E

    This will be an interesting thread moving forward......

    keep up the good work Vetech,and always make sure your on the Ken side of things. LOL
  3. E

    ihi 35j engine ran away on me today?

    thanks for the info STEFANO, I think I have it narrowed down, I don t really need to do an engine swap at this time. these engines have three individual injection pumps and my engine oil smells of fuel. so I am going to start with the three orings that are serviceable at the top side of each...
  4. E

    what to do and what not to do when a engine runs on its own?

    on a bigger engine there is probably some serious air volume pulling in,no t- shirt working there. i have heard of dudes reversing the filter on the seal type. seems dangerous, the built in flapper deal gets my vote
  5. E

    ihi 35j engine ran away on me today?

    on the runaway engine stuff, if its black smoke its fuel, and if its white smoke its oil ? or would every thing be black
  6. E

    what to do and what not to do when a engine runs on its own?

    just had my first run away but it was a small 30hp, I remember a guy at the quarry had a 3406 run away on some type of crusher plant,he tried to get it shut down, but it blew up before he could, he died on the spot . what to do ? and when to run and when to not run? could a smaller engine kill to?
  7. E

    need to buy a good underground utility locater ?

    we found this one by opening the water line at the shutoff in building, then shoved a electrical fish tape down the plastic pipe towards the service pit
  8. E

    ihi 35j engine ran away on me today?

    thanks STEFANO,that is a well laid out service manual, wish they were all like this one.wonder if the governor spring could cam open to much and get stuck, causing it to run away? but why would it do that after operating for 15 min
  9. E

    ihi 35j engine ran away on me today?

    I checked again it said it is a 3LD1, went back today checked fluid levels oil good, coolant was low from overheating.i expected it to be stuck but low and behold, it fired right up and ran fine. I loaded it on the trailer way more ready this time to shut the air off. I did notice the air...
  10. E

    ihi 35j engine ran away on me today?

    it started blowing black smoke and would not shut off, finally died after a minute. wonder if I broke a ring and it ran on the oil? Isuzu 3Ln1 engine I think, never had this happen before what next?
  11. E

    need to buy a good underground utility locater ?

    had two different old timers there, both used this method, both way of
  12. E

    need to buy a good underground utility locater ?

    thanks cm would you buy the HL or just the H model
  13. E

    need to buy a good underground utility locater ?

    well I just spent a full day looking for a water line that should have been found in a hour. what are guys using to locate underground wire/pipes lines. thanks
  14. E

    322bl long reach, stick cylinder barrel cracked beyond repair, need one asap cat part #116-9123

    well I had to send it off to get rebarreled, it developed a small pin hole that I welded up, then a week later this happened. all the cylinder guys I talked to said they have never seen this happen before.
  15. E

    322bl long reach, stick cylinder barrel cracked beyond repair, need one asap cat part #116-9123

    best time I found so far on a machine shop rebuild is 4 weeks
  16. E

    322bl long reach, stick cylinder barrel cracked beyond repair, need one asap cat part #116-9123

    looks like the only new ones are across the pond 10 weeks out minimum, any body know where there is one in the u.s.?
  17. E

    battery cable suppliers

    was going to buy the tempo indent type multi crimper that just threads in out for adjustment said it will crimp the feral on bigger battery connections
  18. E

    battery cable suppliers

    has far has crimpers is the try- form better then the indent type?
  19. E

    I gave notice about starting my pension today!

    idle hands are the devils workshop, old operators don't retire,there filter falls out, they use the word NO a lot more, and get to do whatever they want. enjoy my friend !!
  20. E

    battery cable suppliers

    has far has wire size range, will 2/0 cover most applications or do you think I need to have a bunch of different size wire on hand? was thinking of getting a roll red and black 2/0 then a couple rolls 14ga for lights, control wiring
Top