• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. T

    D6H trans oil level

    thanks for the replies. I checked the breather by the filter housing, looked good. nice and clean
  2. T

    D6H trans oil level

    the pump ready to disassemble, the scavenge gears, scavenge plate, 2 pics of the charge pump plate/housing
  3. T

    D6H trans oil level

    I removed the trans pump so I could take it apart and see what shape its in. There is some scuffs on the flat plates of the scavenge section that I can see but feel smooth when I drag my fingernail across it. I slipped a .010 feeler gauge between the gears teeth where they mesh together. That...
  4. T

    lever berings replace

    I've no experience with that repair so I can't tell you how to do it. Looks like you are on the right track, keep us posted on how its going. Happy Holidays all.
  5. T

    D6H trans oil level

    Jake980, Thanks for the helpful info. I don't notice any problems like loss of power or the trans slipping, it runs good. It is noisy like a howling sound though. I would think everything was ok if it wasn't for the oil level issue and high temp reading on the gauge. Maybe I should follow one...
  6. T

    D6H trans oil level

    thought of some more stuff - installed temp guages recently, so I don't know if it was running hot before that. - Cut open and inspected the trans filter this week, found a few dark specs so small i could barely see them and some small yellow flakes, paint maybe? looked clean other than that...
  7. T

    D6H trans oil level

    Thanks for the replies. Some additional info. It runs fine except after an hour or two the powertrain oil temp starts to climb towards 250-260 degrees. The temp returns to around 200 real quick in neutral. The temp jumps right back up in first gear when I run it back and forth with the blade...
  8. T

    D6H trans oil level

    my D6H ser#4RC1088 trans oil level is doing something odd. after it sits unused for a couple days the oil level on the dipstick, cold oil and engine off, is way low, about 4 gallons or so. When I start it up and get it to operating temp its within the high and low marks for engine at low idle...
  9. T

    963 hydro leaking internally?

    I had a similar problem on my 963, we pulled it apart and replaced the seals on the shaft, put it back together and it worked for awhile then it was leaking again. Turns out the there was an updated shaft that had an additional seal, we installed it and that fixed it. Can't recall my exact...
  10. T

    20 ton tag with broken leaf spring

    thanks for the replies everyone. good advice that I will listen to
  11. T

    20 ton tag with broken leaf spring

    I got a 97 eager beaver 20 ton tag trailer with hutch 9700 leaf spring suspension, the back right spring has 2 of the 7 leafs broke so I'm going to replace it. Any advice on what I'm in for as far as fixing it? Should i replace both springs on that axle and can I reuse the ubolts, etc? I haul...
  12. T

    Installing planetary shafts in final drives?

    How do you install the planetary gear shafts in a D6H (or similar) final drive carrier? The book says lower the temp of the shaft and press into the carrier to the retainer to set the preload on the bearings. I would like to know how tight they fit? Can they be knocked in with a sledge? Or how...
  13. T

    What to do to start a sitting dozer

    Hmmm, I'd drain the engine oil and see if its got any water in it for starters.
  14. T

    D6H scavenge pump failing?

    Thanks for pointing me in the right direction! I put in a new temp switch in today and when I started it up no filter bypass alarm. Woop! I found some damage to the wiring harness and the guard that encloses the pump drive shaft had cracked all the way across on the bottom. I welded up the guard...
  15. T

    D6H scavenge pump failing?

    Nige, Thanks for the reply and the info. I didn't know about the temp switch, it looks like its located in the end of the charge pump. I unplugged the pigtail and put a jumper wire across the harness side contacts and the alarm turns off. I will have to test the temp switch out to see if its...
  16. T

    D6H scavenge pump failing?

    I think my transmission scavenge pump is going bad. Sometimes when I check the oil level its up or down by about 5 gallons. I got around a gallon of oil out of the torque converter when I took the scavenge line off. After starting it and letting it run for a while I shut it off and removed the...
  17. T

    New Truck

    looks good nice looking truck, you'll get into those tight spots no problem
  18. T

    Deere 755 track problem

    whats happening when you pump the grease in? is there a lot of resistance? if not maybe the grease is leaking past the seals. I'm not familiar with the deere design, can you see the recoil spring? any pics?
  19. T

    Can you tell me about this sawhead?

    I've got this old sawhead, it says LDC 206 TENCO on the side and I can't find any info on the internet about the manufacturer. If anyone can tell me about it I would appreciate it. I got it a few years ago at an auction in Florida. Did tenco go under, change its name, get bought by another...
  20. T

    excavator tracks making popping sound in snow

    I wonder if it could be that the snow is building up in the tracks and compressing the recoil spring then quickly letting loose and slamming? or maybe some stiff or frozen track pins or some combination of the two?
Top