• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. J

    Case 650 k stranded!!!!

    That's odd because I have no issues with instrument cluster. All gauges work and read properly. Track speed gauge works when I hit buttons on joystick. I can read software version of instrument cluster within the cluster. Would that code allow the dtc to not release park brake or move?
  2. J

    Case 650 k stranded!!!!

    I have purchased a manual off line. The manual isn't the best in the world. I am now getting fault code of 4621. Park brake still will not release. At the bark brake relay I have switched battery voltage, known good ground. I am not receiving signal out of dtc to complete the circuit. I have ohm...
  3. J

    Case 650 k stranded!!!!

    I checked for voltage at park brake relay. Not getting anything. I traced the wire back as far in harness as I could. But cant determine where the white 52 power wire goes.
  4. J

    Case 650 k stranded!!!!

    I have a case 650k series 2. Iv been dealing with trans faults and no can issues and finally got all that resolved. Now I cannot get park brake to release. Checked all fuses and relays. I'm not recieving voltage at the park brake solenoid. The park brake light stays illuminated with the levers...
  5. J

    Case 750K won't release parking

    The park break sensors seem to be all sound. The machine is not showing any codes. The park brake levers are reading because with both up engine starts. With left lever down engine starts. I can then put just the right lever down and engine will start. I can put both levers down and get a no...
  6. J

    Transmission Fault light on Case 650k Series 2

    One of the one amp fuses for the drivetrain controller the wire was chewed into right at the back of the fuse panel. Fixed broke wire and immediately the no can fault went away. Also the monitor started working for the track speed and fnr would now register on monitor. Only issue im having...
  7. J

    Transmission Fault light on Case 650k Series 2

    I have fixed the issue with the no can from joystick and drive train controller now it seems I have another issue. Park brake will not release. All fuses and relays seems to be ok. With both levers down the park symbol is still illuminated on the dash. Any ideas?
  8. J

    Case 750K won't release parking

    Currently working on a 650k case. Park brake will not release. All fuses and relays seems to be ok. With both levers down the park symbol is still illuminated on the dash. Any ideas?
  9. J

    Transmission Fault light on Case 650k Series 2

    I removed LH armrest and plastic cover. Nothing under the plastic cover but the metal frame of the cab. Everything I'm reading states the can resistance should be 117 ohms. I'm reading 120 ohms. Is that a big enough difference to give me the issues I'm having?
  10. J

    Transmission Fault light on Case 650k Series 2

    Serial # CAL002618
  11. J

    need help with Case 650k dozer wont move

    Currently working on a case 650k series 2. Open cab machine. 1700 hours. Machine has been running fine with zero issues. While dressing up a job the machine was under a light load just dressing up and completely stopped pulling. All hydraulic functions work great. I did verify I have good charge...
  12. J

    Transmission Fault light on Case 650k Series 2

    Also in dash under software version I'm getting a "no can" for joystick and "no can" from dtc. Which I'm assuming is the drive train controller. Also where is the drive train controller located on this machine.
  13. J

    Transmission Fault light on Case 650k Series 2

    Currently working on a case 650k series 2. Open cab machine. 1700 hours. Machine has been running fine with zero issues. While dressing up a job the machine was under a light load just dressing up and completely stopped pulling. All hydraulic functions work great. I did verify I have good charge...
  14. J

    Case 650k not moving in any direction

    Currently working on a case 650k series 2. Open cab machine. 1700 hours. Machine has been running fine with zero issues. While dressing up a job the machine was under a light load just dressing up and completely stopped pulling. All hydraulic functions work great. I did verify I have good charge...
Top