• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Innocent bystander

  1. I

    How would you remove these bushings? Komatsu pc35mr

    I have done all the above but which is best depends on your torch skills, You can cut all the way down through the bushing and not cut the bore but even if you nicked it, it really doesnt hurt anything. I lean towards the welding 4-6 hot passes with a stick welder, throw a bolt or some piece of...
  2. I

    VOLVO EW180B engine not starting

    What version of PTT (Vcads) do you have?
  3. I

    VOLVO EW180B engine not starting

    I can confirm that there is some errors/discrepancy in Prosis concerning cam and crank sensors. I have found that the data is mostly correct however they reverse sensor location with the pictures. In another words they typically show the cam and crank sensors in opposite positions but all the...
  4. I

    VOLVO EW180B engine not starting

    I had one of these exact machines one time that would not start unless I unplugged the VECU, I cant remember if it was shorting/corrupting the data lines or it needs an OK signal from the VECU to start however it would start with it unplugged, ended up replacing VECU. have you tried starting it...
  5. I

    L90G

    96-1 and 96-12 Have the exact same description below. 9-7 Is for Volvo care track and you will always have that code if you don't subscribe to it. 96 Fault mode FMI 12 Detection conditions:The engine control unit (E-ECU) registers: that the rail pressure control is not working correctly...
  6. I

    Volvo L90E

    Had/have a fleet of L90Ds. Es, Fs, Gs and now Hs. Nothing sticks out that I recall. except a ton of Trans shift solenoids, but pretty reliable machines. dont recall any issues with the fuel systems, has unit injectors and belt driven fuel feed pump, was pretty reliable system. At least it does...
  7. I

    Wa120 wont shift out of first gear

    WA120 Dash?? and serial?
  8. I

    D3G LGP right track drives, left does not.

    On the surface I would say something broke in the final as if it was hydraulic or control issue it would not free roll, pull the plug on the final and check for metal.
  9. I

    Komatsu WA200-5

    All later Komatsu loaders are hydrastat, not sure what dash they started but definitely -5 up are. Powershift is just Komatsu's name for their hydrastat trans which uses a variable piston pump and a 2 speed Motor-or variable speed motor, I cant recall for sure and is controlled by a controller(ECM)
  10. I

    Steering VOLVO L120E

    Manualslib.com tradebit.com scribd.com All Volvo tech(including parts) info is now in a program called Prosis, simular to Cat SIS If familiar with that.
  11. I

    Volvo L60G

    229-9 Detection conditions:The engine control unit (E-ECU) registers: that bus communication is missing with ACM (EB52/EB56) Symptom: ○ Red central warning ○ No regeneration is performed Possible causes: ○ Open circuit ○ Short circuit to voltage ○ Short circuit to frame ground ○...
  12. I

    L60G ECU/cam signal

    *Update* Ok here is what I have found so far. All Volvo machines using this E-ECU, Part number 60100011 (fits many loaders, excavators etc with common rail engine) Use Pin A45 and A46 for camshaft sensor input-this is + and - input from a a/c wave form sensor. If I look up aftermarket...
  13. I

    L60G ECU/cam signal

    I have a Volvo L60G. I have 2 different new aftermarket ECUs, one is TRW like the original, both have been programmed for this machine at purchase. Both ecus will NOT read cam sensor, engine runs but don't sound right and has cam sensor code(SE2703-3)I am not familiar with devtool but is there...
  14. I

    Steering VOLVO L120E

    Steering cylinders bypassing, cap of one at a time until it steers or steering wheel locks up.
  15. I

    Bobcat HB880 Hammer reseal?

    I have a Bobcat S300 with a HB880 breaker hammer that is working good but leaking oil. Does anyone have a idea how much it would cost to reseal? Thanks
See more
Top