• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by ljelter1973

  1. L

    953 locked breaks, cat A 1987

    I am not a 100% sure. However I can pressurize to a blow out pressure I guess. 2500 psi. This was with an automotive lift pump. Plumbed it inAnd then it would pressurize pressurize the brakes and Backfeed the pump for the tranny even though the charge point works is fine too.. I'm not sure of...
  2. L

    953 locked breaks, cat A 1987

    Yes,. I just figured out how to reply to posts anyway. Yes One track now can slide while the other 1's been free because I only put the sun shaft back into 1 side I also cleaned out the secondary pump and I can feel the pressure at the head of it builds plenty good. Is there a way to drain...
  3. L

    953 locked breaks, cat A 1987

    Is there a way to bleed behind the Spring load not the pressure side. With a secondary pump I can put plenty of pressure to the pressure side. Thank you very much for anything you can divulge. PS local cat dealer will hall 50 miles for free. Intuition tells me there is a quick fix
  4. L

    953 locked breaks, cat A 1987

    I guess shopping is delayed. Family
  5. L

    953 locked breaks, cat A 1987

    I did put the sunshine back in on one side I meant to say earlier bucket forward and backwards while down and that track just slid the other of course sbutton and thank you very much for anything and for everything you have said.
  6. L

    953 locked breaks, cat A 1987

    Is there a way to get fluidfrom behind the lock Spring in the brakes breaks
  7. L

    953 locked breaks, cat A 1987

    Okay I did the pressurization of the brakes And I put one of the main gears back in and put the bucket up-and-down and I know it's put in pressure to it it's just is there sometime Philip may be let fluid out on the other side of the seal or is there a way to bypass it or I know I'm getting...
  8. L

    953 locked breaks, cat A 1987

    Back to previous post John Deere 310B. Couldn't remember what it was called but now I did It does pool pretty good.
  9. L

    953 locked breaks, cat A 1987

    To Heymccall, I don't doubt it not that I've tried but everything Looks plenty aligned and I'll I see it in the bottom of the hole is a cross one side the cross is straight-up-and-down the other side it's selectly slanted. But neither of them has moved but I can take the bucket and move the...
  10. L

    New purchase 1988 Cat 953 SN 20Z01980

    My SER. Engine 3204 Machine953 pin05z00819 trans 4na034...*9j5378..... . I am a farmer that works on small machinery. This machine was purchased in 06And worked well until 18,19.. This is the first time I have posted anything about it except for asking people around here nobody knows...
  11. L

    New purchase 1988 Cat 953 SN 20Z01980

    Napa had all my 1987 filters. Can find a full manual online for $70. Complete Is repair. Is basically everything. First manual I bought cost 850.00$ $70 was a lot better.
  12. L

    953 locked breaks, cat A 1987

    I have a 953 originally it blew the right hydraulic line going to wheel motor. Lifted the old machine off the ground as far as the tracks are concerned. Recharged it with fluid and eventually I got to move in the air. Drove it about a quarter mile to where it is parked now. Finally found out you...
  13. L

    953 locked breaks, cat A 1987

    I have a 953 originally it blew the right hydraulic line going to wheel motor. Lifted the old machine off the ground as far as the tracks are concerned. Recharged it with fluid and eventually I got to move in the air. Drove it about a quarter mile to where it is parked now. Finally found out you...
See more
Top