• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Tim98TA

  1. T

    Several questions/issues CAT 315L

    Went back out to the machine and connected to the correct port. Engine speed dial set to 10. Went into Calibration Mode #1 and read the gauge. 459psi. Tried to adjust it down through the monitor. Same reading. Tried to adjust it up. Same reading. Adjusted it all the way to -9 and locked it in...
  2. T

    Several questions/issues CAT 315L

    Awesome. Thanks once again Nige!!!!!!!!! Very much appreciated
  3. T

    Several questions/issues CAT 315L

    Anyone? Anyone? Bueller? LOL
  4. T

    Several questions/issues CAT 315L

    Ok, got into calibration mode for the PRV. Had the gauge hooked up and everything was set up as the instructions said. The gauge was always reading about 379-380, even if I tried adjusting the pressure through the monitor. The numbers on the monitor would move, but the gauge stayed the same...
  5. T

    Several questions/issues CAT 315L

    Yes this helps. It shows me how to get into the calibration mode. Thanks a bunch. I will try to get to it next week.
  6. T

    Several questions/issues CAT 315L

    Am I missing something on the monitor? I tried again, but I still do not see any codes/calibration numbers being displayed. I have never had an error code flash on the screen either. I have seen the error symbols(coolant hot and low oil pressure) flash in the bottom portion of the screen, but...
  7. T

    Several questions/issues CAT 315L

    I could not do either calibration. My monitor does not/did not display any readings that would pertain to either calibration. Attached is a picture of my monitor. Maybe mine does not perform the calibrations on the monitor?
  8. T

    Several questions/issues CAT 315L

    Thanks Nige, but I originally bought this machine to do a project on my land that was supposed to last about a year. I'm about 14 months in due to downtime weather, etc. Once the project is done, I will sell the machine. I've spent WAY more than the original plans for any repairs. I just don't...
  9. T

    Several questions/issues CAT 315L

    AWESOME. Thanks so much for the information. I will try to get that done this weekend and let you know how it goes.
  10. T

    Several questions/issues CAT 315L

    A couple of questions to get started. (1) What is the serial number of your machine? 6YM02363 (2) Did you perform the calibration procedure on the new governor actuator after you replaced it? No. I was unaware that needed to be done. How is it done? (3) Why was the main pump changed? The...
  11. T

    Several questions/issues CAT 315L

    1 - A while back I had to change the engine speed control module with the cable. It was a plug and play deal. Before I changed it, the AES would work like it was supposed to. 3 seconds and no demand, goes to idle. Now I have to keep the switch in MANUAL mode and use the RABBIT /...
  12. T

    Cat 315AL stuck in high speed tracking

    Thank you Nige. Much appreciated. Tyler, we recently rebuilt the swivel. It was doing it before then as well.
  13. T

    Cat 315AL stuck in high speed tracking

    Serial #6YM02363 Light switches on monitor if I move it to low speed but the machine does not respond. Being in high speed the machine will not turn on its own. Could it be the low speed solenoid/valve not reacting? I'm not sure of the process when the button is pushed.
  14. T

    Cat 315AL Control Monitor not responding

    Serial Number 6YM02363 The control Monitor does not respond to any functions being pushed. The fuel, coolant temp and oil temp work. The lights by each button lights up and they change position if pushed, but the machine does not respond to any changes. Can it be 'reprogrammed', 'reset'? Or any...
  15. T

    Cat 315 Tracking Issues

    “Must engage gauge tracks some to get machine to swivel” not terribly sure what this means, can you clarify? From sitting still, if you want the machine to swivel, left or right, you must first press the track levers, either frontwards or backwards. Then the machine will swivel. “When tracking...
See more
Top