• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. D

    Oil leak under steering wheel

    In my loading shovel I am getting hydraulic oil leaking up from under it. It works fine when cold but if you start working the machine and steering hard if starts to drip out oil up the top. Is there likely some seal or o ring gone? Any advice on how to tackle this? So the oil comes up and dips...
  2. D

    Bearing in Axle repair

    The bearing holding the pinion shaft broke in my old komatsu wa 120 a few months ago. I need to get it back in action now again . If I remove the axle off the loader, is there crowds who specialise in these and able to take it apart and replace the parts I need. Or would they need the actual...
  3. D

    Backhoe valve sticking.

    It's a 1998 massey 860 backhoe. The tilt and crowd on the back arm sticks on. When you let go of the level if won't return to neutral. It wants to stick on and you would have to pull it back. Also if you had a bucket on it the ram is loosing pressure immediately and the bucket falls from either...
  4. D

    Setting up a rear diff?

    I need to replace part number 8 and 19 innthe below diagram which are bearings in the rear diff of the loading shovel. Is there a big science to set up the diff again after ripping it.
  5. D

    Zexel pump diesel increase

    Where js the screw ro increase the diesel a small bit in a zexel (bosch) pump which is on a 4bd1t engine. Picture attached. Want to turn it 1/4 turn.
  6. D

    Is my exhaust too small?

    Back again. Isuzu 4bd1 turbo in my loading shovel. Just find the engine a bit short of horsepower. I thought it should be just a but quicker to rev up to max etc. There is a non genuine exhaust set up as possibly this isn't the first day engine in this early 90s machine so more than lightly...
  7. D

    Increasing the fuel

    Want about another 10 or 15 hp from my isuzu 4bd1 turbo engine. Is this the right screw towards the right of the picture? If I did 1/8 of a turn would I be safe enough ?
  8. D

    Engine for a loading shovel

    I need to replace the engine in my 1990s loading shovel. Where can I rob engines from that would fit in? Track machine , truck etc? Just wondering what would be set up correctly fueling and rev wise? I see a fair few track machines with the same engines as I need broken if it would be a...
  9. D

    Is this for a manual tach?

    I screwed this piece out of under the oil filter housing. The probe at the end spins as if it's a tacho of some sort? Could it be the tacho for the revs? The engine is a 4bd1 turbo
  10. D

    Oil pressure gauge installation

  11. D

    Isuzu 4bd1

    Have a machine here with an Isuzu 4bd1t engine in it. I'm wondering can I buy a kit with both the sensor, wire and clock which will read the oil pressure. I'm looking for something I can screw into the engine and then have a clock reading the pressure in the cab? I currently have nothing.
  12. D

    Isuzu 4bd1t engine

    Anyone know where I can plug a tacho cable into in a 4bd1t engine? The altenator doesn't have this function for it. I was hoping maybe there was a sender unit I could buy and plug into the 4bd1t engine somewhere to read revs and hours
  13. D

    Replacing a 4 cylinder engine with a 6 cylinder

    It's a furukawa fl310. It current has an Isuzu 4bd1 4 cylinder turbo engine in it. I'm wondering could I fit in an Isuzu 6 cylinder 6bd1 engine instead. I could push the rad back a few inchs. I'm wondering though will it bolt in at the front or not,
  14. D

    Weak tilt

    It's a komatsu Wa100. Year is 1994 i think. It's very weak in the tilt position. Was pushing up silage and was getting caught trying to flick the silage. Will lift up and down no problem but it's weak on the tilting. Zero leaks anywhere in the hydraulics. Is this due to a weak hydraulic pump...
  15. D

    Where to find a vin number

    Where are vin numbers typically on a loading shovel. It's a 1991 furukawa loading shovel. Are they generally only on a plate or are they stamped somewhere on the machine itself. I found the plate with the serial number but cannot find the vin number so help appreciated. This is a Japanese...
  16. D

    Anyone able to identify this axle

    What brand of axle is this? Are they a commonly used axle? Its off a komatsu wa180. Also what is the correct oil for it?
  17. D

    Furukawa loader

    Hi would anyone know what hydraulic filter a furukawa fl310 takes? The numbers are gone off the original filter so we have nothing to cross reference.
  18. D

    How can I get my temperature gauge working again

    I have a Clark michigan 35b. It has an isuzu engine. It starts first first click. However all gauges have been disconnected and wiring removed. I would like to slowly but surely get them. Working again. I presume the picture below is where the tempature sender is just by the thermostat...
  19. D

    Clark michigan parts

    Does anyone know who does parts for Clark michigan 35b? Looking for brake parts. It has oil immersed brakes.
  20. D

    Tcm 830

    Hi does anyone know of a firm which sell parts for tcm loaders? Looking for brake parts . Also anywhere where I could buy a workshop manual/parts manual for a tcm 830
Top