• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Angry Mike

    Final Drive Oil Analysis

    Ah i stand corrected, my dealer has us do it at every 500 so i assumed that was a CAT standard
  2. Angry Mike

    ANOTHER WHAT KIND OF TOOL IS THIS

    That's a hammer
  3. Angry Mike

    Final Drive Oil Analysis

    Cat procedure is every 500hrs
  4. Angry Mike

    Genie S-40 Boom lift joysticks stopped working.

    The green LEDs only activate when a input is received, ex a joystick motion or toggle sw
  5. Angry Mike

    Cat serial number lookup for options.

    I can look it up for you tommarow, sis is down right now
  6. Angry Mike

    Cat 335 next gen boom moving out on its own

    Also try the last 4 and last 5 of the s/n as service code , my dealer and another out west here use that
  7. Angry Mike

    Case tv380 ATS Fail Error Code 3766

    ATS - aftertteatment system. Prob associated with the delta P sensor. Check the delta P sensor wiring, 5lbs pull test on wires. Check for 5v ref. Disconnect the 2 lines on either side and make sure they are not blocked internally or kinked
  8. Angry Mike

    Genie S-40 Boom lift joysticks stopped working.

    The yellow will flash the code, then they will flash several times simultaneously, then the red will flash code, and repeats. Did you try resetting the joystick?
  9. Angry Mike

    299D No regen

    Most all cats will require the parking brake to be set, no accelerator input, engine coolant temp above 140 degrees, and SCR temp above 600 degrees
  10. Angry Mike

    Looking at new jumping jack compactors any comments on what your thoughts are on various brands?

    MTX-60 and MTX-70. We have about 15 of each and they seem to to great. Go through spark plugs alot
  11. Angry Mike

    Best machines to get into heavy equipment rental?

    I work at a caterpillar rental store, our top money makers are 50' towable lifts, dump trailers, 16' tilt trailers, jumping jacks, and 185cfm mobile compressors
  12. Angry Mike

    Charging systems

    Is it in a area in which you are able to take a photo of the resistor?
  13. Angry Mike

    Need AC wiring schematic for a CAT 259D Compact Track Loader

    Check the thermostatic swith 2 wire harness. The pins commonly go bad
  14. Angry Mike

    Need AC wiring schematic for a CAT 259D Compact Track Loader

    There are 3 relays to the right of the compressor. The one that feeds the compressor is the middle one
  15. Angry Mike

    Injection pump removal

    the pump shop i ordered a replacement from wants it back for a core.. plunger was siezed and the bore is pretty scored up
  16. Angry Mike

    Injection pump removal

    I got it. Was just really really tight fit lifting off the studs from plunger spring pressure and i didn't want to hulk it.. thanks
  17. Angry Mike

    Injection pump removal

    Hey all, have a perkins 404D-22 on a genie lift. Its a cassette type pump and the instructions say to loosen bolts , lift it and remove a clip for linkage. After loosening bolts it barely comes up off the block. Anyone run into this problem?
  18. Angry Mike

    Cat GP25N forklift,, very weird problem

    Have a CAT gp25n forklift, SN AT35A00442. I have a P-04 and F -04 DTC. (No communication between VCM and ECM. also with engine off and key on. Number 2 ignition coil gets extremely hot and smokes
  19. Angry Mike

    2013 318D Crank no Start

    not a good practice to "wet" compression test a diesel.. if your fuel and compression are both good. That just leaves air and timing, one of them is not good
  20. Angry Mike

    Trailer tire problem

    Are they retreads?
Top