• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. C

    Takeuchi tl12v2 auxiliary hydraulic issues

    I have a takeuchi tl12v2 with hydraulic issues. Whenever I am using my power rake or any other auxiliary attachment like a trencher or an auger, the attachment will lose hydraulic pressure and stop spinning as soon as I raise or lower the boom or tilt up/down. Any ideas on what the issue could...
  2. C

    2004 JCB 520 Telehandler Transmission Oil

    I have a 2004 JCB 520 telehandler and was wondering what type of transmission oil I can put in it?
  3. C

    2011 Vermeer V8550A Trencher

    My 2001 vermeer V8550A trencher is having issues where it will trench perfectly fine for about 15 minutes and then quit and will not work until I let it cool down for a few hours. The trencher will still work in reverse, just not forward until I let it cool down.
  4. C

    Cat 297c rear axle removal

    Ok thats good to know. Mine is missing all the washers. I'm guessing it is normal for that shaft I be able to move side to side a little bit unless it needs to be tight.
  5. C

    Cat 297c rear axle removal

    Do you know what the fix is to get rid of side to side slop on front axle shaft? I'm not sure if it is supposed to have washers or if its just worn out. I've attached picture of what I'm talking about. Every time I turn sharp and can feel to thump to one side.
  6. C

    Cat 297c rear axle removal

    No it has the Grease zerts along the axle shaft on the track roller assembly
  7. C

    Cat 297c rear axle removal

    The Grease zerts won't take Grease and I can't get them to with my Grease rejuvinatoe Ok thanks, I didn't even think of trying that yet. Thats a good idea. I'll try that tomorrow and see how it goes. Thanks
  8. C

    Cat 297c rear axle removal

    The Grease zerts won't take Grease and I can't get them to with my Grease rejuvinator either
  9. C

    Cat 297c rear axle removal

    Yes it is but the axle shaft is seized onto track frame so I am having to remove entire rear axle shaft.
  10. C

    Cat 297c rear axle removal

    Does anyone have any experience with removing rear axle on cat 297c? I am trying to remove rear left side axle and it seems as though the rear nuts are impossible to get a wrench onto inside machine.
  11. C

    Cat 297C running rough

    Ended up being a clogged inlet fitting on fuel pump housing.
  12. C

    c3.4 misfire and blues smoke

    It is a cat 297c
  13. C

    c3.4 misfire and blues smoke

    I have fuel being pumped to injection pump. It will runs great for about 10 minutes and then start running rough like its not getting fuel. Then once I idle it down and let it recover for about a minute or so it will run fine for about 5 minutes again
  14. C

    c3.4 misfire and blues smoke

    Did you end up figuring out what issue was on your machine? I am having similar problem.
  15. C

    Cat 297C running rough

    I have tried a few other things with no luck. Machine still stumbles and misfires at full throttle. I checked the codes and am only getting codes in Mode 2. The codes are 91-3 and 2471-3. Any clues on what else i should check. Could it possible be bad injectors?
  16. C

    Cat 297C running rough

    No I haven't tried that yet. I will check for codes and let you know if I find any. Thank you very much
  17. C

    Cat 297C running rough

    X Yes I cleaned out passages in filter head and blew out all of fuel lines with compressed air and machine is still running the same.
  18. C

    Cat 297C running rough

    Serial number for the machine is CAT0297CCGCPOO782. I've installed new fuel transfer pump, filters, and drained fuel tank and am still having same issues. Runs rough at full throttle sometimes, revs down by itself and blows what looks like blue smoke when running rough. Any other suggestions...
  19. C

    Cat 297C running rough

    Yes my machine is a 297c as well. All I've tried so far is replacing fuel filter but will still do same thing after a few hours of running machine.
  20. C

    Cat 297C running rough

    Did you ever end up figuring out what the problem was? I am having same issue with my machine.
Top