southernman13
Senior Member
Looking for a 36" bucket for this machine also may look at 42/48 bucket. I'm in Fl/Ga. area thanks. Ricksouthernboom@bellsouth.net used bucket unless super deal on new. Thanks
-
Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!
SK250LC Kobelco bucket
- Thread starter southernman13
- Start date
clintm
Senior Member
- Joined
- Jul 7, 2013
- Messages
- 974
- Location
- charlotte nc
- Occupation
- trucking,concrete recycling,grading, demolition
whats the pin size I have a couple that may fit
southernman13
Senior Member
3.54in/90mm. 12.88in wide
clintm
Senior Member
- Joined
- Jul 7, 2013
- Messages
- 974
- Location
- charlotte nc
- Occupation
- trucking,concrete recycling,grading, demolition
I wil check tomorrow I am pretty sure that I have something that will fit
southernman13
Senior Member
Hey that's awsome. My email address is in the OP. If you could reply to that I'll get it quicker. Thanks also I can give you any measurements off it you need. Thanks again
willie59
Administrator
20.33 pin center line spacing.
clintm, if you have a 36" or 42" for an SK330/SK350 I'd dang sure be interested.
clintm, if you have a 36" or 42" for an SK330/SK350 I'd dang sure be interested.
Truck 505
Well-Known Member
I have a 36" Werk Brau that might be what you all need. It has a tool box on the back and I have the ripper for it. Not sure what the measurements are.
I can get them tomorrow maybe depending on how bad Gramps dumps on me tonight and tomorrow.
I can get them tomorrow maybe depending on how bad Gramps dumps on me tonight and tomorrow.
clintm
Senior Member
- Joined
- Jul 7, 2013
- Messages
- 974
- Location
- charlotte nc
- Occupation
- trucking,concrete recycling,grading, demolition
I know I have some for 300 komatsu's it's the same pin size the kobelco is a little wider they are 36"or less trenching buckets I don't use the narrow ones
willie59
Administrator
Yeah, the 300 Kommie is around 13 1/2" width, the 330/350 Kobelco is near 15" stick width.
Truck 505
Well-Known Member
The bucket is a Werk Brau.
Width between ears: 17.875"
Center of pin to center of pin: 23.5"
Pin Diameter: 3.9375"
The bucket is 36" wide. Digs about 38" or 39" with new teeth
The has X400WT twin tiger teeth on it and I have four new ones for it.
The bucket has a Hensley lip and tool box.
It was used on a Kobelco Sk400-3
Width between ears: 17.875"
Center of pin to center of pin: 23.5"
Pin Diameter: 3.9375"
The bucket is 36" wide. Digs about 38" or 39" with new teeth
The has X400WT twin tiger teeth on it and I have four new ones for it.
The bucket has a Hensley lip and tool box.
It was used on a Kobelco Sk400-3
Attachments
Last edited:
willie59
Administrator
3.9375 is the 100mm pin, the SK330/350 size bucket I need uses 90mm pin. Drat!
Truck 505
Well-Known Member
All the pin holes have bushings in them. You could cut the old ones out and find some with a smaller inside diameter.
willie59
Administrator
True, it could be done, I'll pitch the idea to the boss and see if he's interested.
Truck 505
Well-Known Member
Sounds good
southernman13
Senior Member
There's a bunch on iron planet today