• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by moss

  1. M

    Volvo L120d workshop manual

    Thanks for the link. That will help a lot. Moss
  2. M

    Volvo L120d workshop manual

    Hello all I am hoping someone here may have a Volvo L120d manual. Thanks in advance Moss
  3. M

    Workshop manual Volvo L120 d

    Hi all Would anyone have a workshop manual for a 2002 Volvo L120d wheel loader. Thanks in advance
  4. M

    Hitachi EX-120 manual

    Thank you so much Tool King. Every little bit of info helps.
  5. M

    Hitachi EX-120 manual

    Hello Tool King, Would you have a shop manual for Hitachi 120-2 ?? Many thanks in advance. nicmoss2@gmail.com
  6. M

    NTN bearing

    Sorry guys found it.....having a grey moment.SF3607VPX2 Thanks
  7. M

    NTN bearing

    Hello all, Does anyone out there have the NTN Bearing number for the angular contact bearings in a PC60/3 drive the part number is TZ850A1021-00 in the parts book. I only have a small shop where I am who can order in but I need a bearing number as the part number just shows up blank...
  8. M

    kubota V1902 shop manual

    Yep that is what I've been using,so far as you say no issues either. A shop manual would be nice though just for tolerences ,torque etc. We are in the bush up here but I like to do things to some degree of accuracy ,even given most of the gear is old and been messed with alot. Moss
  9. M

    No oil in Final drive

    Hi fourwheelinj 1, You may be lucky and it is only an "O" ring on the face plate. Remove clip ring and both plugs then rotate track until there is a sun gear behind each plug hole,wind in a correct sized bolt gently and the faceplate should pop out easily.(Or at least that is the case for...
  10. M

    kubota V1902 shop manual

    Thanks Lantraxco, I was looking at doing a rebuild on this one but once I pulled it down I found a crack in the block so I will just put in a donor one as there are plenty kicking about here. Perchance you wouldn't have any manuals,shop and or parts for a PC60-3 would you? Thanks again Moss
  11. M

    kubota V1902 shop manual

    Hi all, Does anyone out there have a shop manual for a Kubota V1902 shop manual. It's the same donk thats in a NH 555 or KH 52 excavator. Thanks in advance Moss
  12. M

    PC60/3 shop manual

    Or even a parts book for a 60/3 would help. Thanks Moss
  13. M

    PC60/3 shop manual

    Hello all. I am looking for a shop manual and parts manual for a PC60/3 ,anyone out there with one? Also a 4D95L shop manual would be awesome. It would make life alot easier . Thanks in advance. Moss
  14. M

    D5M service codes

    Thanks John and Nukem, I will return to our main workshop and see if we got schematics for wiring when I pick up test tool. So all will checked. The machine is parked up for now so that no damage is caused while the fault is checked. John could you explain where the speed sensors are located...
  15. M

    D5M service codes

    Hi all , Found the codes online so all good. Turns out to be Action alarm Service brake pedal switch Transmission Auto/Manual switch Downshift switch As I said the machine have alot of water through it for quarantine and was probably run while wet,so my guess is the faults occurred then...
See more
Top