• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Jbullfrog

    Does anyone have a 16" bucket that will fit a Case CX50B near Western Iowa?

    I have a footing job for a garage and they are wanting 16" footings. It's in 3' of fill so digging with a smaller bucket and making them wider isn't a good option. I have a Werk-Brau pin grabber setup for 1-3/4 pins on 9" centers and 6-1/8" wide between the ears.
  2. Jbullfrog

    Parts for Older Stanley MB250 and 350 breakers

    I have a MB250 that is leaking between the top and main body. I took it to my Case dealer to see if it would take a charge, and it wouldn't. They said the urethane top hat is no longer available and suggested I look at a newer hammer. I found an MB05 in my price range. I called Stanley to check...
  3. Jbullfrog

    Replacing heater in an 1845C and looking for ideas on plumbing

    I have an 1845C with a Simms cab and the Zero Start heater box. The compression fittings on the back started to leak, so I pulled it out and found the ferrules were wore into the tubes croaked and it couldn't be saved. I got a replacement and cut the new tubes to accept the 90 deg compression...
  4. Jbullfrog

    Werk-Brau rock or frost bucket question

    I have an 18" WB bucket that is supposed to fit a Deere 315 SC. I have a frost shank that I use on my 5 ton excavator and have no use for this bucket. I'm located in western Iowa. Make me an offer.
  5. Jbullfrog

    Werk-Brau 18" rock or frost bucket $1000 or offer

    It is pinned for a Deere loader backhoe, but could have the bushings changed to go to different pin diameters. Teeth look like they haven't been used. Located in Avoca, Iowa. call 4o2-98o-2694 Thread title and posted information edited at member's request.
  6. Jbullfrog

    Ford and New Holland Construction Service manuals

    I have a set of dealer Service manuals for Ford and New Holland skid loaders, backhoes, and wheel loaders. Asking $50 plus shipping of $13.50 for flat rate box. Bounce me with what you are looking for. I'll get a list and more pictures posted also. Located in Avoca, IA.
  7. Jbullfrog

    It's little, but is a scraper!

    I hooked on to our landlord's Duplex Mfg. "hydraulic scoop" with my little Ford tractor. I know it hadn't moved in the 25 years we have farmed for him. Surprisingly, the tires took air and hold! I'm using it to haul stumps and roots I had grabbed out with my mini to the burn pile.
  8. Jbullfrog

    Looking for Hoes or Dynapac trencher parts

    Does anyone know of salvage yards with tile trenchers? Looking for sidehill cylinders close the Germany. Who else works with tiling machines? I'm in Iowa and most of the parts come from Northland Trenching, but we are looking for any other sources for Hoes or Dynapac machines.
  9. Jbullfrog

    Problem with Fuel Shut-off on 2001 era Case 1845C

    The last year I've been poping the Safety Interlock fuse randomly. Sometimes it's ok for days and sometimes it will pop 3 in a few minutes. I've checked all the harness and have found no chaffing or damage. I've checked the arm bar switch, seat switch, and solenoid. We finished harvest, so I...
  10. Jbullfrog

    HS6000 Stanley vibrating plate compactor with Case 580S mounts

    I have a great working plate compactor. Looking for $3500. I have a 5 ton excavator and want to downsize to a narrower plate. This one is 23-1/2" x 34". It is setup for a 580S Case backhoe. I'm in Avoca, Iowa (40 miles from Omaha). Call 4o2-98o-2694, or email j.johnsonservices@fmctc.com
  11. Jbullfrog

    Sometimes the big excavators need dug out with a compact excavator

    I had a buddy call and wanted me to load and get to his excavator asap, as it was sinking. He was digging a tile line across a swampy area. He made it 100' and then got to the base of a dam and started sinking. I laid some cedar trees down and tracked down around his tail to dig around the back...
  12. Jbullfrog

    Need ideas on getting goo out of water jacket of block from 7000 4cyl Ford tractor

    I have a 7000 Ford diesel in the shop that had the oil cooler leaking into the radiator. It has a lot of goo in the bottom of the water jacket. I had to split it to replace a leaking frost plug on the back of the block and found the goo when I drained the water. The engine is still together with...
  13. Jbullfrog

    Is there a suspension seat available for a Case CX50B

    I spent the day removing asphalt and concrete from streets for patches. The seat in our CX50B has slightly more cushion than a folding chair, My lower back is really feeling it. Is there a Case seat, or an aftermarket seat or suspension system that will fit in a mini?
  14. Jbullfrog

    Has anyone seen or used a Cat TH360B with the basket controls?

    There are 3 contractors in my area that have Cat telehandler. All of them complain about having to use a ladderto get to the basket. There is an electrical connection on the boom for a control, but Cat doesn't seem to offer it anymore. I found a picture of a Cat basket with a control console...
  15. Jbullfrog

    Need some help with an estimate - I normally do hourly, but this is way bigger.

    Looking at a plan for spread footings 24" deep by 36" or 42" wide. There is about 650' of 36" and 130' of 42". I normally do terrace repair and digging for pipe repair, so I haven't charged by the foot before. Is there a calculator available? I will also need to figure for sheepsfooting or...
  16. Jbullfrog

    What size are the auxillary hydraulic valves on a Case CX50B?

    I built a hanger for our McMillen auger drive and need to make a set of adapters to plug it in. I need to know the size of the o-ring fittings to go into the aux shut off valves. I have a thumb on it, but it has smaller lines with #8 JIC fittings. I want to connect to Case flatface skidloader...
  17. Jbullfrog

    Forsale McCloskey 621 Trommel Screener and extra drums

    We have a McCloskey 621 screener and 3 full drums plus a selection of screens from 2" - 5". Unit was used for mulch and tire processing. Currently located at Avoca, IA. 2006 model with 2131 hrs. Cat diesel power with remote up/down and side control of front conveyer. Asking $190,000 for unit and...
  18. Jbullfrog

    Wildcat CX700AM compost turner for sale

    I have a Wildcat compost turner. It came from a large feedlot that was using it for manure composting. 3-point mounted, requires 100-150hp tractor. I can email pictures and answer any questions. Located near Avoca, Iowa and we can load it. E-mail j.johnsonservices@fmctc.com or call...
  19. Jbullfrog

    Someone lost the key for our 621 McCloskey Trommel. What else fits it?

    We need to move our 621 screener and can't find the key to start it. What other equipment key will fit it? thanks,
  20. Jbullfrog

    2 sets of AirBoss tires on 6 bolt Wheels for sale

    I have 2 sets of 10.5x16 AirBoss segmented tires for sale. They are about 3/4 tread. One set has a few segments torn, but I have spares to fill them in. We sold our 1840, so we don't need these. Asking $900 a set. call 4o2-98o-2694 or email j.johnsonservices@fmctc. com
Top